TEC Motors

Reliance is an authorised distributor of TEC motors.

TECA Series Aluminium Housing Motors

  • A High Quality range of standard Industrial Motors suited to a wide range of Industrial applications.
  • Frame Sizes 63 to 160-
    • 09kW to 37kW 2 Pole.TEC-motor
    • 06kW to 30kW 4 Pole.
    • 09kW to 22kW 6 Pole.
  • Efficiency IE1 and IE2 (where applicable)
  • Multi mount up to 30kW.
  • Voltage: 3kW and below 230/400V, 4kW and above 400/690V.
  • Enclosure IP55 as standard (IP56 or IP65 as options)
  • Complete with PTC Thermal protection as standard.
  • Bearing located on non drive end as standard.
  • Sealed bearings used on all frame sizes for Aluminium Housing Motors.
  • Various modifications available (Force Vent Kit, Special Voltages, Special Output shaft / Double output shaft, Drip Cover, Tropicalised Winding, epoxy paint, Anti-Condensation Heaters)

Read more

TEC ECOL Cast Iron Housing Motors

  • A High Quality range of standard Industrial Motors suited to a wide range of Industrial applications.
  • Frame Sizes 80 to 355 –Tec-Cast-Iron
    • 75kW to 315kW 2 Pole.
    • 75kW to 315kW 4 Pole.
    • 75kW to 250kW 6 Pole.
    • 2kW to 220kW 8 Pole.
  • Efficiency IE1, IE2 and IE3 (where applicable)
  • Removable feet up to Frame size 280.
  • Voltage: 3kW and below 230/400V, 4and above 400/690V.
  • Enclosure IP55 as standard (IP56 or IP65 as options)
  • Complete with PTC Thermal protection as standard.
  • Bearing located on non drive end as standard.
  • Sealed bearings used on frame sizes up to 132, for 160 Frame and above open bearings are used.
  • Various modifications available (Special Voltages, Special Output shaft / Double output shaft, Drip Cover, Tropicalised Winding, epoxy paint, Anti-Condensation Heaters) .

Read more

TEC ATEX Range ATEX-TEC

  • Zone 1 (2G)
    • Aluminium Housing 63-132 Frame – Exd 2G IIC T4.
    • Cast Iron Housing 160 – 355 Frame – EExde 2G IIC T4.
  • Zone2 (3G)
    • Aluminium Housing 63-160 Frame – 3G ExnA IIC T4 Gb.
    • Cast Iron Housing 180 – 355 Frame – 3G ExnA IIC T4 Gb.
  • Zone 1/21 (2GD)
    • Aluminium Housing 63-132 Frame – 2GD Exd IIC T4 Ex tb IIIC T1250
  • Zone22 (3D)
    • Aluminium Housing 63-160 Frame – 3D Ex tD IIIC T1250
    • Cast Iron Housing 160 – 355 Frame – 3D Ex tD IIIC T1250

 

TECA-BM Series Aluminium Housing Motors with an Electromagnetic DC Brake

  • Frame Sizes 63 to 160-
    • 18kW to 18.5kW 2 Pole.TEC-alum-braked
    • 18kW to 15kW 4 Pole.
    • 25kW to 11kW 6 Pole.
  • 205VDC Brake for Motor powers up to 3kW with full wave rectifier, 190VDC Brake with a half wave rectifier for 4kW and above.
  • Multi mount in all cases.
  • Voltage: For 400V Supply in all cases.
  • Enclosure IP55 as standard
  • Complete with PTC Thermal protection as standard.
  • Bearing located on non drive end as standard.
  • Sealed bearings used on all frame sizes.

 

TPC Series Aluminium Housing Motors 1 Phase Permanent Capacitor Motors

  • Frame Sizes 56 to 112 –TEC-CAp-START
  • Frame Sizes 56 to 100 –
    • 09kW to 2.2kW 2 Pole.
    • 06kW to 2.2kW 4 Pole.
  • Suitable for most Fan applications (Starting Torque 0.5 -0.9 Times full load torque)
  • Voltage: For 230V 1 Phase Supply.
  • Enclosure IP55 as standard
  • Sealed bearings used on all frame sizes.
  • Note it is recommended that single phase motors are not started / stopped more than 15 Times per Hour to allow safe discharge of capacitors.

 

TCC Series Aluminium Housing 1 Phase Cap start / Cap run Motorstec-motor

  • Frame Sizes 56 to 112 -37kW to 3.0kW 2 Pole.
    • 25kW to 3.7kW 4 Pole.
  • Suitable for Most High Starting Torque Applications (Starting Torque 1.8 -2.5 Times full load torque)
  • Voltage: For 230V 1 Phase Supply.
  • Enclosure IP55 as standard
  • Sealed bearings used on all frame sizes.
  • Note it is recommended that single phase motors are not started / stopped more than 15 Times per Hour to allow safe discharge of capacitors.